|
|
| Author |
Message |
Bruevich
Moderator
Joined: 12 Feb 2006
Posts: 235
|
 Posted: Sat Feb 18, 2006 1:45 am Post subject: Smart clip operation guide |
 |
|
Operation instruction
(standard unlock procedure for P2K models)
1. Power on the Smart-Clip and E/G indicator will light green.
2. Power on the phone without SIM card and flash card (if present).
3. Connect phone to Smart-Clip and press the "Unlock" button ( red on older clips ).
4. E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
5. E/G will light green on success or red on error
6. Successful unlock resets User Code to 1234, Security Code to 000000
* Pinout Motorola P2K to USB A Standard Cable
* Pinout Motorola P2K to USB A Forced Boot Mode Cable
Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedure
1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success.
When you unlock Sendo phone use either fully charged phone battery OR power supply from Smart-Clip. Don't use them both at the same time! If you use power supply from Smart-Clip, make sure current is not less than 300mA, otherwise not all data will be properly recorded to the phone.
* Pinout Sendo snd2xx snd3xx snd6xx
* Pinout Sendo snd5xx
* Pinout Sendo snd8xx
Unlock procedure for A1000 Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Disassemble the phone
2. Connect repair USB cable (pin 13 and 14 shortened)
3. Connect testpoint A to testpoint B
4. Connect phone battery
5. Push Button 1 and Button 2 simultaneously
6. Press "Search" button in SmartMoto
7. SmartMoto should find "S Blank Paragon POG", or "S Blank Rainbow POG"
8. Disconnect testpoint
9. Open unlock tab in SmartMoto
10. Select A1000 from phone models list
11. Press "unlock via testpoint"
12. The handset is unlocked & ready to be assembled.
Unlock procedure for E770 and V3x Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please remember:
During testpoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board.
Unlocking Motorola V3 (boot ver.8.26)
You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode.
5. Part of phone firmware is reflashed.
6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).
Unlocking Motorola V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others Motorola models with boot 0.6.3.1
You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode, reserve copy of security area is created.
5. Part of phone firmware is reflashed.
6. Phone doesn't power on after that. SmartMoto will give you the message requiring to take phone into boot mode using keys combination: *,#, PWR ON (at this moment the phone has to be connected by usb cable) or using Repairing cable.
7. Press "OK" button. Wait till the process ends.
8. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).
Motorola V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking note
Unlocking newer versions of V18x/V22x/C65x/C38x/E375/E378i or C975/C980/V980/E1000 (Boot Loader 0.6.1.2) may require additional user intervention.
It may happen that E/G led still blinks after display turns off - it means that you have to turn the phone ON manually within 2-3 seconds after display turns off; alternatively you can try to unlock this newer version of V18x/V22x/C65x/C38x/E375/E378i with battery charger on.
Unlock procedure for Motorola A920/A925/A1000
1. Power the phone on.
2. Connect the phone to a powered clip. Phone display should give "USB cable connected" message.
3. Press UNLOCK button on the clip.
4. Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
5. Press 1 and 2 keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these 2 keys during "Waiting for PST" message, the clip will give red E/G led and you will have to start with step 1 again).
6. After A and B keys have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
7. Green E/G led glows. The cell phone is unlocked.
Motorola Axxx/Exxx/Vxxx unlocking note
Don't unplug cable right after phone reboot, wait until E/G led stops blinking!
Motorola E396/E398 unlocking note
Remove flash card from phone before unlocking
Motorola C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedure
1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success *
* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)
* Pinout Motorola C115 C116 C117 C155 C156 V170 V171
* Pinout Motorola E365
Unlock procedure for V3 (RAZR) Motorola phone by downgrading boot using testpoint (boot version 8.26)
1. Perform V3 testpoint procedure
2. Flash it with V3_boot_7.E.0.smf file.
3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Unlock procedure for C975 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform C975 testpoint procedure
2. Flash it with C975_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform C975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for C980 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform C980 testpoint procedure
2. Flash it with C980_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform C980 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for E1000 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform E1000 testpoint procedure
2. Flash it with E1000_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform E1000 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V975 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V975 testpoint procedure
2. Flash it with V975_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V980 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V980 testpoint procedure
2. Flash it with C980_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V980 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V1050 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V1050 testpoint procedure
2. Flash it with V1050_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V1050 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for C390 Motorola phone with testpoint (boot version 8.26)
1. Perform C390 testpoint procedure
2. Flash it with C390_boot_7.d2.smf file.
3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Unlock procedure for V360 Motorola phone with testpoint (boot versions starting from 8.A0)
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V360 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Unlock procedure for E1, L6, L7, U6, V190 Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any E1, L6, L7, U6 or V190 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Unlock procedure for V3i Motorola phone with testpoint (boot versions starting from 8.A0)
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V3i testpoint procedure (Please note: temporarialy you must choose Motorola V360 from a list in SmartMoto)
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V3i handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Smart-Clip upgrade procedure
1. Connect Smart-Clip to PC using LPT cable
2. Power Smart-Clip ON (warning: don't use battery!)
3. Go to our Upgrade Zone
4. Upgrade Zone uses ActiveX element, answer "Yes" to install and run it
5. Press "Connect"
6. Press "Update" if your version is out of date
7. Power Smart-Clip OFF
8. Disconnect LPT cable
_________________
Don't argue with an idiot, he will bring you down to his level and beat you up with his own experience... |
|
| Back to top |
|
 |
| |
Ads |
Google Adsense
Sponsor
|
|
Guest
|
| Posted: Tue Apr 04, 2006 5:35 pm Post subject: Re: Smart clip operation guide |
|
|
| Bruevich wrote: | Operation instruction
(standard unlock procedure for P2K models)
1. Power on the Smart-Clip and E/G indicator will light green.
2. Power on the phone without SIM card and flash card (if present).
3. Connect phone to Smart-Clip and press the "Unlock" button ( red on older clips ).
4. E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
5. E/G will light green on success or red on error
6. Successful unlock resets User Code to 1234, Security Code to 000000
* Pinout Motorola P2K to USB A Standard Cable
* Pinout Motorola P2K to USB A Forced Boot Mode Cable
Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedure
1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success.
When you unlock Sendo phone use either fully charged phone battery OR power supply from Smart-Clip. Don't use them both at the same time! If you use power supply from Smart-Clip, make sure current is not less than 300mA, otherwise not all data will be properly recorded to the phone.
* Pinout Sendo snd2xx snd3xx snd6xx
* Pinout Sendo snd5xx
* Pinout Sendo snd8xx
Unlock procedure for A1000 Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Disassemble the phone
2. Connect repair USB cable (pin 13 and 14 shortened)
3. Connect testpoint A to testpoint B
4. Connect phone battery
5. Push Button 1 and Button 2 simultaneously
6. Press "Search" button in SmartMoto
7. SmartMoto should find "S Blank Paragon POG", or "S Blank Rainbow POG"
8. Disconnect testpoint
9. Open unlock tab in SmartMoto
10. Select A1000 from phone models list
11. Press "unlock via testpoint"
12. The handset is unlocked & ready to be assembled.
Unlock procedure for E770 and V3x Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please remember:
During testpoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board.
Unlocking Motorola V3 (boot ver.8.26)
You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode.
5. Part of phone firmware is reflashed.
6. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).
Unlocking Motorola V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others Motorola models with boot 0.6.3.1
You need to use SmartMoto to unlock these models.
1. Power on the phone.
2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
4. Phone goes into boot mode, reserve copy of security area is created.
5. Part of phone firmware is reflashed.
6. Phone doesn't power on after that. SmartMoto will give you the message requiring to take phone into boot mode using keys combination: *,#, PWR ON (at this moment the phone has to be connected by usb cable) or using Repairing cable.
7. Press "OK" button. Wait till the process ends.
8. The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).
Motorola V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking note
Unlocking newer versions of V18x/V22x/C65x/C38x/E375/E378i or C975/C980/V980/E1000 (Boot Loader 0.6.1.2) may require additional user intervention.
It may happen that E/G led still blinks after display turns off - it means that you have to turn the phone ON manually within 2-3 seconds after display turns off; alternatively you can try to unlock this newer version of V18x/V22x/C65x/C38x/E375/E378i with battery charger on.
Unlock procedure for Motorola A920/A925/A1000
1. Power the phone on.
2. Connect the phone to a powered clip. Phone display should give "USB cable connected" message.
3. Press UNLOCK button on the clip.
4. Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
5. Press 1 and 2 keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these 2 keys during "Waiting for PST" message, the clip will give red E/G led and you will have to start with step 1 again).
6. After A and B keys have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
7. Green E/G led glows. The cell phone is unlocked.
Motorola Axxx/Exxx/Vxxx unlocking note
Don't unplug cable right after phone reboot, wait until E/G led stops blinking!
Motorola E396/E398 unlocking note
Remove flash card from phone before unlocking
Motorola C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedure
1. Power off the phone
2. Connect clip to the phone using RJ45 cable (pinouts below)
3. Press UNLOCK button
4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
5. E/G led will glow green on success *
* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)
* Pinout Motorola C115 C116 C117 C155 C156 V170 V171
* Pinout Motorola E365
Unlock procedure for V3 (RAZR) Motorola phone by downgrading boot using testpoint (boot version 8.26)
1. Perform V3 testpoint procedure
2. Flash it with V3_boot_7.E.0.smf file.
3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Unlock procedure for C975 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform C975 testpoint procedure
2. Flash it with C975_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform C975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for C980 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform C980 testpoint procedure
2. Flash it with C980_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform C980 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for E1000 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform E1000 testpoint procedure
2. Flash it with E1000_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform E1000 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V975 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V975 testpoint procedure
2. Flash it with V975_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V980 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V980 testpoint procedure
2. Flash it with C980_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V980 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for V1050 Motorola phone with testpoint (boot versions starting from 6.36)
Downgrade boot method
1. Perform V1050 testpoint procedure
2. Flash it with V1050_boot_5.F.1.smf file
3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V1050 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for C390 Motorola phone with testpoint (boot version 8.26)
1. Perform C390 testpoint procedure
2. Flash it with C390_boot_7.d2.smf file.
3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.
Unlock procedure for V360 Motorola phone with testpoint (boot versions starting from 8.A0)
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V360 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Unlock procedure for E1, L6, L7, U6, V190 Motorola phone with testpoint
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform corresponding testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any E1, L6, L7, U6 or V190 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Unlock procedure for V3i Motorola phone with testpoint (boot versions starting from 8.A0)
Using "Unlock via Testpoint" function of SmartMoto method
1. Perform V3i testpoint procedure (Please note: temporarialy you must choose Motorola V360 from a list in SmartMoto)
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V3i handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.
Smart-Clip upgrade procedure
1. Connect Smart-Clip to PC using LPT cable
2. Power Smart-Clip ON (warning: don't use battery!)
3. Go to our Upgrade Zone
4. Upgrade Zone uses ActiveX element, answer "Yes" to install and run it
5. Press "Connect"
6. Press "Update" if your version is out of date
7. Power Smart-Clip OFF
8. Disconnect LPT cable |
|
|
| Back to top |
|
|
| |
Ads |
Google Adsense
Sponsor
|
|
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
